[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
RE: Router with bandwidth management
Hello Mark,
>John, I've had experience with Packeteer, and unless they cleaned up their
>act, they are no good with high load of multiple traffic variables and
>types.
I don't know much about them, but I see they have a nice GUI.
>Have you heard of ETINC - www.etinc.com - although this would be a dedicated
>box.
This solution is quite expensive at more than $2000 a box (at last
look). The guy that sells this is very famous for being a difficult person
-- from what I know, he does the programming and tech support (not a recipe
for friendly tech support). And it can't do much more unless you are a
linux guru -- better to go with the linux or bsd option then. The Mikrotik
box is $495 with these features.
>If Robert already has a Cisco router as specified earlier, it's a
>cheaper alternative.
Certainly, but it depends on how must power the Cisco box has -- Cisco puts
the lowest power cpu possible for routing in most boxes and you need to
check the shaping throughput.
John
www.mikrotik.com
>Regards,
>
>Mark Tinka - CCNA
>Network Engineer
>Africa Online Uganda
>5th Floor, Commercial Plaza
>7 Kampala Rd,
>Tel: +256-41-258143
>Fax: +256-41-258144
>E-mail: mtinka at africaonline.co.ug
>Web: www.africaonline.co.ug
>
>
>-----Original Message-----
>From: John Tully [mailto:tully at mikrotik.com]
>Sent: Saturday, May 17, 2003 2:39 PM
>To: mtinka at africaonline.co.ug; 'Robert'; afnog at afnog.org
>Subject: RE: Router with bandwidth management
>
>
>You could also use lower cost alternatives.
>
>Linux and BSD have some special builds that provide this for free.
>
>Also, RouterOS has some easy to use bandwidth shaping features -- $25 for
>an OEM license.
>http://www.mikrotik.com/Documentation/manual_2.7/Root/Queue.html
>
>There are also a number of boxes priced similar to Cisco -- Packeteer is
>one example
>
>John
>www.mikrotik.com
>
>At 01:44 PM 5/17/2003 +0300, Mark Tinka wrote:
> >Well, if you choose to go with Cisco, they support some form of
> >bandwidth
> >management called rate-limiting.
> >
> >With rate-limiting, you can asign minimum, maximum and burst bandwidth
> >to
> >a specific IP address and/or network range. Here's a sample configuration:
> >
> >conf t
> > access-list 100 remark 32Kbps to Wireless Client XXX
> > access-list 100 permit ip host 192.168.0.200 any
> > access-list 100 permit ip any host 192.168.0.200
> >
> > int e0/0
> > rate-limit input access-group 100 32000 8000 16000 conform-action
> > transmit exceed-action drop
> > rate-limit output access-group 100 32000 8000 16000 conform-action
> > transmit exceed-action drop
> >
> >As you can see above, the access list that matches your wireless
> >client's
> >IP address is placed onto the Ethernet interface that is connected to your
> >wireless segment. In the rate-limit statement on the Ethernet interface,
> >32000 is the bits per second allowed, 8000 is the normal burst bytes and
> >16000 is the maximum burst bytes. As the last few lines say, if the user's
> >IP address conforms to this setting, transmit his packets through. If the
> >assigned capacity is exceeded, begin to apply congestion control -
> >basically, drop packets exceeding allocated capacity.
> >
> >Rate-limiting is supported on only the 2600 series chassis and above.
> >From
> >experience, it doesn't work on the 1600 nor the 1700 series Cisco routers.
> >
> >Regards,
> >
> >Mark Tinka - CCNA
> >Network Engineer
> >Africa Online Uganda
> >5th Floor, Commercial Plaza
> >7 Kampala Rd,
> >Tel: +256-41-258143
> >Fax: +256-41-258144
> >E-mail: mtinka at africaonline.co.ug
> >Web: www.africaonline.co.ug
> >
> >-----Original Message-----
> >From: owner-afnog at afnog.org [mailto:owner-afnog at afnog.org] On Behalf Of
> >Robert
> >Sent: Friday, May 16, 2003 9:50 PM
> >To: afnog at afnog.org
> >Subject: Router with bandwidth management
> >
> >Who can propose to me an entry level router with bandwidth mangement
> >for
> >my small wireless isp network?
> >
> >Regards
> >
> >Robert Longla
>
>
>
>
>
>-----
>This is the afnog mailing list, managed by Majordomo 1.94.5
>
>To send a message to this list, e-mail afnog at afnog.org
>To send a request to majordomo, e-mail majordomo at afnog.org and put
>your request in the body of the message (i.e use "help" for help)
>
>This list is maintained by owner-afnog at afnog.org
-----
This is the afnog mailing list, managed by Majordomo 1.94.5
To send a message to this list, e-mail afnog at afnog.org
To send a request to majordomo, e-mail majordomo at afnog.org and put
your request in the body of the message (i.e use "help" for help)
This list is maintained by owner-afnog at afnog.org