[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: FreeBSD router
A natd.conf sample file is hereby attached.
I hope this helps.
#
# $FreeBSD: src/sbin/natd/samples/natd.cf.sample,v 1.5 1999/09/13 18:18:33 ru Exp $
#
#
# Configuration file for natd.
#
#
# Enable logging to file /var/log/alias.log
#
log yes
#
# Incoming connections. Should NEVER be set to "yes" if redirect_port
# or redirect_address statements are activated in this file!
#
# Setting to yes provides additional anti-crack protection
#
deny_incoming no
#
# Use sockets to avoid port clashes. Uses additional system resources, but
# guarantees successful connections when port numbers conflict
#
use_sockets yes
#
# Avoid port changes if possible when altering outbound packets. Makes rlogin
# work in most cases.
#
same_ports yes
#
# Verbose mode. Enables dumping of packets and disables
# forking to background. Only set to yes for debugging.
#
verbose no
#
# Divert port. Can be a name in /etc/services or numeric value.
#
port 8668
#
# Interface name or address being aliased. Either one,
# not both is required.
#
# Obtain interface name from the command output of "ifconfig -a"
#
# alias_address 192.168.0.1
interface rl0
#
# Alias unregistered addresses or all addresses. Set this to yes if
# the inside network is all RFC1918 addresses.
#
unregistered_only no
#
# Configure permanent links. If you use host names instead
# of addresses here, be sure that name server works BEFORE
# natd is up - this is usually not the case. So either use
# numeric addresses or hosts that are in /etc/hosts.
#
# Note: Current versions of FreeBSD all call /etc/rc.firewall
# BEFORE running named, so if the DNS server and NAT are on the same
# machine, the nameserver won't be up if natd is called from /etc/rc.firewall
#
# Map connections coming to port 30000 to telnet in my_private_host.
# Remember to allow the connection /etc/rc.firewall also.
#
#redirect_port tcp my_private_host:telnet 30000
#
# Map connections coming from host.xyz.com to port 30001 to
# telnet in another_host.
#redirect_port tcp another_host:telnet 30001 host.xyz.com
#
# Static NAT address mapping:
#
# ipconfig must apply any legal IP numbers that inside hosts
# will be known by to the outside interface. These are sometimes known as
# virtual IP numbers. It's suggested to use the "interface" directive
# instead of the "alias_address" directive to make it more clear what is
# going on. (although both will work)
#
# DNS in this situation can get hairy. For example, an inside host
# named aweb.company.com is located at 192.168.1.56, and needs to be
# accessible through a legal IP number like 198.105.232.1. If both
# 192.168.1.56 and 198.105.232.1 are set up as address records in the DNS
# for aweb.company.com, then external hosts attempting to access
# aweb.company.com may use address 192.168.1.56 which is inaccessible to them.
#
# The obvious solution is to use only a single address for the name, the
# outside address. However, this creates needless traffic through the
# NAT, because inside hosts will go through the NAT to get to the legal
# number, even when the inside number is on the same subnet as they are!
#
# It's probably not a good idea to use DNS names in redirect_address statements
#
#The following mapping points outside address 198.105.232.1 to 192.168.1.56
#redirect_address 192.168.1.56 198.105.232.1