[afnog] MikroTik Router Wireless
John Tully
tully at mikrotik.com
Wed Jul 13 10:38:55 EAT 2005
The running flag for the wireless AP will only show 'R' when at least one
station is connected.
John
>On Tuesday 12 July 2005 11:59, you wrote:
> > > I have now changed the mode from station to ap-bridge and the
> > > band from 5GHz to 2.4GHz. The IP addresses of the interfaces
> > > are the same.
> > >
> > > Unfortunately, I still do not detect any wireless connections arround.
> > > Any other suggestions please?
> >
> > Hmm, I don't understand, changing from station should have sorted you
> > out, -tried the usual restarting stuff?- aanyway please send the
> > following output:
> >
>----------------------------------------------------------------------------------------
>
> > /interface print
>[admin at MikroTik] interface> print
>Flags: X - disabled, D - dynamic, R - running
> # NAME TYPE RX-RATE TX-RATE MTU
> 0 R ether1 ether 0 0 1500
> 1 R ether2 ether 0 0 1500
> 2 R ether3 ether 0 0 1500
> 3 wlan1 wlan 0 0 1500
> 4 wlan2 wlan 0 0 1500
>[admin at MikroTik] interface>
>
>
> > /ip address print
>[admin at MikroTik] interface> /ip address print
>Flags: X - disabled, I - invalid, D - dynamic
> # ADDRESS NETWORK BROADCAST INTERFACE
> 0 X 192.168.0.1/24 192.168.0.0 192.168.0.255 wlan1
> 1 192.168.1.1/24 192.168.1.0 192.168.1.255 wlan2
> 2 X 10.1.0.1/24 10.1.0.0 10.1.0.255 ether1
> 3 10.1.1.1/24 10.1.1.0 10.1.1.255 ether3
> 4 X ;;; MikroTik test at home
> 10.1.254.27/24 10.1.254.0 10.1.254.255 ether1
> 5 ;;; Wireless connectivity
> 80.87.65.249/29 80.87.65.248 80.87.65.255 wlan1
> 6 ;;; MikroTik Test in the office
> 80.87.64.57/24 80.87.64.0 80.87.64.255 ether1
>[admin at MikroTik] interface>
>
>
> > /interface wlan1 print
>[admin at MikroTik] interface> print from=wlan1
>Flags: X - disabled, D - dynamic, R - running
> # NAME TYPE RX-RATE TX-RATE MTU
> 0 wlan1 wlan 0 0 1500
>[admin at MikroTik] interface>
>
>
> > /interface wlan2 print
>[admin at MikroTik] interface> print from=wlan2
>Flags: X - disabled, D - dynamic, R - running
> # NAME TYPE RX-RATE TX-RATE MTU
> 0 wlan2 wlan 0 0 1500
>[admin at MikroTik] interface>
>
>
> > /interface wireless print
>[admin at MikroTik] interface> wireless print
>Flags: X - disabled, R - running
> 0 name="wlan1" mtu=1500 mac-address=00:0C:42:05:00:17
> arp=enabled disable-running-check=no
> interface-type=Atheros AR5413 radio-name="000C42050017"
> mode=station ssid="mikrotik" area=""
> frequency-mode=manual-txpower country=no_country_set
> antenna-gain=0 frequency=5180 band=5ghz scan-list=default
> rate-set=default
> supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
> supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,
> 48Mbps,54Mbps
> basic-rates-b=1Mbps basic-rates-a/g=6Mbps
> max-station-count=2007 ack-timeout=dynamic
> tx-power=default tx-power-mode=default
> noise-floor-threshold=default periodic-calibration=default
> burst-time=disabled fast-frames=no dfs-mode=none
> antenna-mode=ant-a wds-mode=disabled
> wds-default-bridge=none wds-ignore-ssid=no
> update-stats-interval=disabled default-authentication=yes
> default-forwarding=yes default-ap-tx-limit=10000000
> default-client-tx-limit=10000000 hide-ssid=no
> security-profile=default disconnect-timeout=3s
> on-fail-retry-time=100ms preamble-mode=both
>
> 1 name="wlan2" mtu=1500 mac-address=00:0C:42:05:00:46
> arp=enabled disable-running-check=no
> interface-type=Atheros AR5413 radio-name="000C42050046"
> mode=ap-bridge ssid="gabus" area=""
> frequency-mode=manual-txpower country=no_country_set
> antenna-gain=0 frequency=2437 band=2.4ghz-onlyg
> scan-list=default rate-set=default
> supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
> supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,
> 48Mbps,54Mbps
> basic-rates-b=1Mbps basic-rates-a/g=6Mbps
> max-station-count=2007 ack-timeout=dynamic
> tx-power=default tx-power-mode=default
> noise-floor-threshold=default periodic-calibration=default
> burst-time=disabled fast-frames=no dfs-mode=none
> antenna-mode=ant-b wds-mode=disabled
> wds-default-bridge=none wds-ignore-ssid=no
> update-stats-interval=disabled default-authentication=yes
> default-forwarding=yes default-ap-tx-limit=0
> default-client-tx-limit=0 hide-ssid=no
> security-profile=default disconnect-timeout=3s
> on-fail-retry-time=100ms preamble-mode=both
>
>[admin at MikroTik] interface>
>
>NOTE: The Flag doesn't show.
>
> >
> > If you just changed the frequency ensure that your cards - on the
> > PC/laptop are on the corresponding frequency. Then try scanning again.
> > Also shut one of the cards down and check for any transmissions, They
> > could be interfering with one another but that ascertion is neither here
> > nor there..first send the output from the above, then we can take it
> > from there.
> >
> > **Gitau
> > Safaricom "The Better Option"
>
>_______________________________________________
>afnog mailing list
More information about the afnog
mailing list